Top 10 Construction Site Hazards and How to Control Them
Construction remains one of Australia's most dangerous industries, and Safe Work Australia treats it as a priority industry for preventing work-related deaths and serious injuries. Understanding the most common hazards and their controls is fundamental to working safely and is a core part of the White Card unit, CPCWHS1001.
The legal references below are to the model WHS Act and Regulations, which apply (with local variations) in every state and territory except Victoria. Victoria uses the Occupational Health and Safety Act 2004 and OHS Regulations 2017. Victoria's rules on falls, excavation, noise and confined spaces cover the same hazards, but some thresholds and terms differ, so check WorkSafe Victoria guidance if you work there.
Test your hazard knowledge
Practice hazard identification questions in our Hazard Identification topic.
1. Falls from Height
Falls from height are one of the leading causes of death in Australian construction. SafeWork NSW describes falls as the leading cause of fatalities and traumatic injuries in the NSW building and construction industry. Nationally, Safe Work Australia's statistics rank falls from a height among the most common causes of worker deaths across all industries, behind vehicle incidents. Under the model WHS Regulations, construction work that involves a risk of a person falling more than 2 metres is high risk construction work and needs a Safe Work Method Statement (SWMS). The duty to manage fall risks applies at any height, not only above 2 metres.
Common scenarios: Working on roofs, scaffolding, ladders, elevated work platforms, open edges, penetrations, and skylights.
Controls: Eliminate the need to work at height where possible. Use passive fall prevention (guardrails, edge protection) before active systems (harnesses). Scaffolding from which a person or thing could fall more than 4 metres must be erected, altered and dismantled by a worker with the appropriate scaffolding high risk work licence, and scaffolds must be inspected before use and regularly after that. Never use makeshift platforms. See our Working at Heights topic for detailed rules.
2. Electrical Hazards
Contact with live electrical sources can cause electrocution, burns, arc flash, and secondary injuries from falls. Construction sites have a combination of temporary power supplies, overhead power lines, and underground cables that create significant risk.
Common scenarios: Contact with overhead power lines (cranes, scaffolding, long materials), cutting into live cables, faulty power tools, damaged extension leads, and working in wet conditions.
Controls: Use residual current devices (RCDs) to protect portable electrical equipment on construction sites. Keep plant and materials outside the safe approach distances for overhead power lines set by your state's electrical regulator or network operator. Use isolation, lockout and tagout before working on electrical equipment. Inspect leads and tools before use and make sure they have been tested and tagged as your site requires. Before digging, lodge an enquiry with Before You Dig Australia (BYDA, formerly Dial Before You Dig) and then locate services on site, as BYDA plans are indicative only.
3. Manual Handling Injuries
Safe Work Australia's statistics consistently show body stressing (injuries from lifting, carrying, pushing, pulling and awkward or repetitive movements) as the most common cause of serious workers' compensation claims in Australia, accounting for more than a third of serious claims in 2023-24. Repetitive lifting, carrying heavy materials and working in awkward postures can cause long-term damage to backs, shoulders, knees and wrists. The model Code of Practice Hazardous manual tasks sets out how to manage these risks.
Common scenarios: Lifting bags of cement, carrying plasterboard, bricklaying, repetitive hammering, and working overhead.
Controls: Use mechanical aids (trolleys, forklifts, hoists) wherever possible. Reduce load weights and sizes. Rotate tasks to limit repetitive strain. Train workers in safe lifting technique: feet shoulder-width apart, bend at the knees, keep the load close, and never twist while lifting. See our Manual Handling topic.
4. Struck-By Hazards
Being hit by falling objects and being hit by moving vehicles or plant are among the most common causes of worker deaths in Australia, alongside falls. The combination of overhead work, mobile plant and material deliveries creates constant struck-by risk on construction sites.
Common scenarios: Tools or materials dropped from scaffolding, reversing vehicles and plant, crane loads swinging, and debris from demolition.
Controls: Install toe boards and mesh on scaffolding to prevent objects falling. Establish exclusion zones under overhead work. Use spotters for reversing vehicles. Secure all loads during crane lifts. Wear hard hats and hi-vis clothing at all times.
5. Trenching and Excavation Collapse
Safe Work Australia's Code of Practice on excavation work warns that collapses happen quickly, which makes it hard for workers to escape. Soil is heavy: the UK Health and Safety Executive notes that a cubic metre of soil can weigh more than 1.5 tonnes, depending on conditions. Under the model WHS Regulations, construction work in or near a trench or shaft with an excavated depth greater than 1.5 metres, or in or near a tunnel, is high risk construction work and needs a SWMS.
Common scenarios: Unsupported trench walls, excavation near existing structures or roads, water ingress weakening soil, and vibration from nearby machinery.
Controls: Shore or batter trench walls to prevent collapse. Keep heavy loads and equipment away from trench edges. Provide safe means of entry and exit, such as ladders or ramps, close to where people are working. Never enter an unsupported trench. Conduct geotechnical assessments on unstable ground.
6. Hazardous Substances
Construction workers are exposed to a range of hazardous chemicals and substances that can cause acute poisoning, chronic disease, or cancer. Silica dust, asbestos, lead paint, solvents, epoxy resins, and cement are among the most dangerous.
Common scenarios: Cutting concrete or stone (silica dust), disturbing asbestos-containing materials during renovation, using solvent-based products in confined areas, and handling cement without gloves.
Controls: Consult Safety Data Sheets (SDS) before using any chemical. Use wet cutting methods to suppress dust. Check the asbestos register or have an asbestos survey done before demolition or refurbishment, and use a licensed asbestos removalist where the WHS Regulations require one (for example, any amount of friable asbestos, or more than 10 square metres of non-friable asbestos; in the ACT a licence is needed to remove any amount). Provide appropriate RPE (respiratory protective equipment) and make sure tight-fitting respirators are fit-tested to the wearer.
Engineered stone: Because of the risk of silicosis from respirable crystalline silica, the use, supply and manufacture of engineered stone benchtops, panels and slabs has been prohibited across Australia since 1 July 2024, with limited exceptions. Cutting other silica-containing materials such as concrete, bricks and natural stone still needs dust controls.
7. Noise Exposure
Prolonged exposure to high noise levels causes irreversible hearing loss. The exposure standard for noise in the WHS Regulations is an 8-hour equivalent continuous level (LAeq,8h) of 85 dB(A) or a peak level (LC,peak) of 140 dB(C). Victoria's OHS Regulations use the same figures. Common construction tools such as concrete saws, jackhammers and angle grinders can be loud enough to exceed the standard well within a normal shift.
Controls: Substitute noisy equipment with quieter alternatives where possible. Use engineering controls such as acoustic enclosures. Schedule noisy work when fewer workers are present. Provide hearing protection (earmuffs or moulded earplugs) and ensure workers wear them correctly. Under the model WHS Regulations, a PCBU must provide audiometric (hearing) testing for workers who are frequently required to wear hearing protection to protect against noise above the exposure standard. The first test must be within 3 months of starting that work, and further tests at least every 2 years.
8. Heat Stress
Australia's climate makes heat stress a serious risk, particularly in northern regions and during summer months. Heat exhaustion and heat stroke can be life-threatening. Workers performing heavy physical tasks in direct sun are most at risk.
Common scenarios: Roofing in summer, working inside unventilated structures, wearing full PPE in hot conditions, and dehydration.
Controls: Schedule heavy work during cooler hours. Provide shade structures and rest areas. Ensure adequate hydration (water stations accessible at all times). Implement a buddy system to watch for heat illness symptoms. Acclimatise new workers gradually. Know the warning signs: dizziness or faintness, nausea or vomiting, weakness, high body temperature, and confusion or reduced consciousness. Confusion, collapse or seizures in a hot worker are a medical emergency, so call 000. The Australian and New Zealand Committee on Resuscitation notes that some people with severe heat illness stop sweating, but not all do, so do not wait for dry skin before acting. See our first aid guide for the response steps.
9. Confined Spaces
Confined spaces on construction sites include tanks, vats, pipes, manholes, tunnels, and underbelly areas of buildings. The risks include oxygen deficiency, toxic atmospheres, engulfment, and entrapment. Construction work carried out in or near a confined space is high risk construction work and needs a SWMS.
Controls: Eliminate the need to enter confined spaces where possible (use remote inspection cameras, long-handled tools). Conduct atmospheric monitoring before and during entry. Issue a confined space entry permit before anyone enters, as the WHS Regulations require. Station a standby person outside the space to monitor the workers inside. Ensure rescue procedures and equipment are in place before any entry.
10. Mobile Plant and Vehicles
Forklifts, excavators, cranes, trucks, and elevated work platforms create serious crush, collision, and rollover risks. The interaction between pedestrians and mobile plant is one of the most critical safety challenges on any construction site, and construction work in an area where powered mobile plant is moving is listed as high risk construction work.
Controls: Establish designated traffic management plans separating pedestrian and vehicle zones. Use spotters for reversing vehicles. Make sure operators hold a high risk work licence where one is required (for example, forklifts and most cranes). Plant such as excavators and loaders does not need an HRWL, but operators must still be trained and competent. Conduct pre-start checks daily. Maintain safe distances from operating plant. Use exclusion zones around cranes and excavators.
Applying the Hierarchy of Controls
For every hazard listed above, the approach should follow the Hierarchy of Controls: eliminate, substitute, isolate, engineer, administer, and then PPE as a last resort. Most real-world situations require a combination of controls from multiple levels. The White Card test will ask you to identify the most effective control for a given scenario β always look for the option highest on the hierarchy.
Key Takeaways
- Falls from height remain one of the leading causes of death in Australian construction
- Every hazard can be managed using the Hierarchy of Controls
- High-risk construction work requires a SWMS before starting
- PPE is the last line of defence, not the first
- Report hazards straight away. Workers must take reasonable care for their own and others' safety and follow reasonable instructions (model WHS Act, s 28), which on most sites includes reporting hazards
Sources and further reading (last reviewed November 2026)
WHS rules differ between states and change over time. Where this page states a legal or regulatory fact, it is based on the official sources below. If anything here disagrees with them, the official source wins. You can read how we check and correct our content.
- High risk construction work requiring a SWMS: duties tool (Safe Work Australia)
- Model WHS Regulations, consolidated 1 July 2024 (PDF, Safe Work Australia)
- Key Work Health and Safety Statistics Australia, latest release (Safe Work Australia)
- Behind the numbers: what's causing harm at work (Safe Work Australia)
- Model Code of Practice: Managing the risk of falls at workplaces
- Construction incident information releases (SafeWork NSW)
- Model Code of Practice: Excavation work (Safe Work Australia)
- Excavations (UK Health and Safety Executive)
- Model Code of Practice: Hazardous manual tasks
- Model Code of Practice: Managing noise and preventing hearing loss at work
- Noise (WorkSafe WA)
- Engineered stone ban (SafeWork NSW)
- Asbestos licences: Class A and Class B (WorkSafe WA)
- Scaffolding licences (WorkSafe Queensland)
- Model Code of Practice: Confined spaces
- Before You Dig Australia (BYDA)
- ANZCOR Guideline 9.3.4: Heat induced illness (hyperthermia)
- Occupational Health and Safety Act 2004 and Regulations 2017 (WorkSafe Victoria)
Test Your Hazard Knowledge
Practice hazard identification and risk assessment questions for your White Card.
Start Practice Test