Skip to content
⚑

Electrical & Excavation Safety

Electrical hazards and underground services pose life-threatening risks on construction sites. This section covers electrical safety isolation procedures, working near overhead power lines (approach distances set by state regulators and network operators), locating underground services before excavation (Before You Dig Australia, formerly Dial Before You Dig), excavation safety including shoring and benching, and confined space entry requirements.

43 questions | 12 easy, 19 medium, 12 hard

Study Guide: Electrical & Excavation Safety

Review these sample questions before starting the practice test.

Q1: What is the safe approach distance for overhead powerlines when using a crane?
  • A. 1 metre
  • B. As close as needed
  • C. It varies by voltage and state β€” for example, at least 3 metres for lines up to 132 kV under NSW guidance, and more for higher voltages βœ“
  • D. 10 centimetres

Safe approach distances for cranes and plant near overhead powerlines depend on voltage and on your state's rules. NSW guidance has used 3 m for lines up to 132 kV, 6 m for 132–330 kV and 8 m above 330 kV; Victoria and other states set their own 'no go zones'. Always check the state regulator's rules and contact the network operator.

Q2: What is a residual current device (RCD)?
  • A. A safety device that detects current imbalance and quickly cuts power to prevent electrocution βœ“
  • B. A type of electrical meter
  • C. A battery backup system
  • D. A circuit breaker for overloads only

An RCD detects imbalances between active and neutral conductors (indicating current leaking to earth, possibly through a person) and cuts power within milliseconds to prevent electrocution.

Q3: How often must RCDs be tested on a construction site?
  • A. Once a year
  • B. Only when they trip
  • C. Daily (push-button test) and regularly by a competent person βœ“
  • D. Never β€” they are maintenance-free

On construction sites, portable RCDs should be push-button tested daily (or before each use) and have an operating-time test by a competent person every 3 months; fixed RCDs are push-button tested monthly and time-tested every 12 months. This follows AS/NZS 3012 (construction and demolition sites).

Q4: What does "lockout/tagout" (LOTO) mean?
  • A. Locking the site office and tagging the door
  • B. Locking tools in a toolbox
  • C. A procedure to isolate energy sources and prevent accidental re-energisation during maintenance or repair βœ“
  • D. Signing out equipment

Lockout/tagout is a safety procedure where energy sources (electrical, hydraulic, pneumatic) are physically isolated and locked, with tags attached to prevent accidental re-energisation during work.

Q5: Before digging or excavating, what must be done to locate underground services?
  • A. Lodge an enquiry with Before You Dig Australia (BYDA, formerly Dial Before You Dig) to obtain plans of underground utilities, then locate them on site βœ“
  • B. Nothing β€” just dig carefully
  • C. Ask neighbours where pipes are
  • D. Only check for water pipes

Before any excavation, lodge an enquiry with Before You Dig Australia (BYDA, formerly Dial Before You Dig) to obtain plans of underground services (gas, water, electricity, communications), then locate and expose them on site using a locator and non-destructive digging.

Q6: What is the purpose of shoring in an excavation?
  • A. To support the walls of the excavation and prevent collapse onto workers βœ“
  • B. To make the excavation deeper
  • C. To waterproof the excavation
  • D. To store materials

Shoring supports the walls of an excavation using hydraulic, timber, or steel props to prevent soil collapse, which can trap, crush, or suffocate workers in the trench.

Q7: At what depth must a trench be secured against collapse by shoring, benching or battering?
  • A. At least 1.5 metres deep βœ“
  • B. Any depth
  • C. 5 metres
  • D. 10 metres

Under the WHS Regulations, a trench at least 1.5 metres deep must be secured against collapse by shoring, benching or battering (unless a geotechnical engineer advises otherwise). Shallower excavations can still collapse, so all excavations need a risk assessment based on soil and site conditions.

Q8: What is "battering" in the context of excavation safety?
  • A. Sloping the sides of an excavation to a safe angle to prevent collapse βœ“
  • B. Hitting the ground with equipment
  • C. A type of concrete technique
  • D. Waterproofing the excavation walls

Battering (or benching) involves sloping the sides of an excavation back to a safe angle, reducing the risk of wall collapse. The angle depends on soil type and conditions.

Ready to practice all 43 questions? Start the interactive quiz below.

of 43
electrical-excavationDifficulty: ●○○

What is a residual current device (RCD)?

More Electrical & Excavation Safety Questions

8 more worked examples with answers and explanations.

Q9: What should be placed around an open excavation?
  • A. Barricading, safety signs, and edge protection to prevent falls into the excavation βœ“
  • B. Nothing β€” workers should be aware
  • C. Decorative fencing
  • D. Only a single cone

Open excavations must have barricading or fencing, warning signage, and edge protection (guardrails) to prevent workers, the public, and vehicles from falling in.

Q10: What is the danger of working near underground electrical cables?
  • A. No danger if you wear rubber boots
  • B. Electrocution and arc flash, which can cause severe burns or death βœ“
  • C. Cables are always de-energised underground
  • D. Only a risk during storms

Striking underground electrical cables during excavation can cause electrocution and arc flash, resulting in severe burns, blast injuries, or death. Always locate cables before digging.

Q11: What should you do if you accidentally damage an underground gas pipe during excavation?
  • A. Cover it back up
  • B. Try to repair it yourself
  • C. Immediately stop work, evacuate the area, eliminate ignition sources, and call the gas emergency number βœ“
  • D. Continue digging more carefully

If a gas pipe is damaged: stop work immediately, evacuate the area, do not use phones or ignition sources nearby, establish an exclusion zone, and call the gas emergency number.

Q12: What is an isolation procedure for electrical work?
  • A. Moving electrical equipment to a separate room
  • B. Wrapping wires in electrical tape
  • C. A procedure to disconnect, lock, tag, and verify that electrical energy is isolated before work begins βœ“
  • D. Testing equipment while powered on

Electrical isolation involves switching off power, locking the switch, attaching a danger tag, and testing to verify the circuit is dead before any electrical work begins.

Q13: Who can perform electrical work on a construction site?
  • A. Only a licensed electrician or person supervised by a licensed electrician βœ“
  • B. Any worker with a hand tool
  • C. Anyone who has read the manual
  • D. The site manager

Only licensed electricians or persons under the direct supervision of a licensed electrician can perform electrical work. This includes repairs, modifications, and connections.

Q14: What is the purpose of a spotter during excavation work near services?
  • A. To spot good restaurants for lunch
  • B. To take photographs
  • C. To watch for and warn the excavator operator about underground services and other hazards βœ“
  • D. To manage traffic

A spotter assists the excavator operator by watching for signs of underground services (colour-coded markers, change in soil), warning of hazards, and guiding safe digging.

Q15: What colour identifies underground electrical cables in Australia?
  • A. Blue
  • B. Orange βœ“
  • C. Yellow
  • D. White

In Australia, underground electrical cables and conduits are identified by orange conduit and orange marker tape (AS/NZS 3000 refers to marker tape to AS/NZS 2648.1). Always check BYDA plans and locate services on site, as older installations may not be marked.

Q16: What is an arc flash?
  • A. A type of camera flash
  • B. A welding technique
  • C. A lightning strike
  • D. An explosive release of energy caused by an electrical fault, producing intense heat, light, and pressure βœ“

An arc flash is an explosive release of energy from an electrical arc, producing extreme heat, intense light, a pressure wave and molten metal. It can cause severe burns, eye damage and blast injuries, even without direct contact.

Key facts for this topic

  • Before excavation starts, the person with management or control of the workplace must take all reasonable steps to obtain current information about underground essential services, such as through Before You Dig Australia (model WHS Regulations, r 304). Source
  • Work in or near a trench or shaft deeper than 1.5 metres is high risk construction work requiring a SWMS (r 291), and such trenches must be secured against collapse by shoring, benching or battering (r 306). Source
  • Work near overhead or underground electric lines is high risk construction work. State and territory regulators and network operators set the minimum approach distances, so check the local rules before working near power lines. Source

Common mistakes

A common mistake is assuming that a service shown on a plan is exactly where the plan says. Plans are a guide only, so services must be located on site, for example by careful hand or vacuum excavation, before machine digging. Students also forget that spoil and plant must be kept back from the trench edge, because extra weight near the edge causes collapses.

Keep studying

Sources and further reading (last reviewed November 2026)

WHS rules differ between states and change over time. Where this page states a legal or regulatory fact, it is based on the official sources below. If anything here disagrees with them, the official source wins. You can read how we check and correct our content.

By WhiteCard Prep Team Last reviewed: November 2026. WHS laws differ between states and territories; Victoria uses its own OHS laws. Check your state regulator for local rules.

Continue Studying

This guide is free and kept up to date by one person. β˜• Support it