PPE on Construction Sites: The Complete Guide
Personal protective equipment sits at the bottom of the Hierarchy of Controls, but it remains an essential part of every construction worker's daily routine. PPE is your last line of defence when higher-level controls cannot fully eliminate a risk. This guide covers every major type of PPE used on Australian construction sites, the relevant Australian Standards, and the legal obligations of both employers and workers.
Practice PPE questions
Test your knowledge with our PPE practice questions covering selection, use, and maintenance.
Why PPE Matters (and Why It Is the Last Resort)
Under section 17 of the model Work Health and Safety Act, a person conducting a business or undertaking (PCBU) must eliminate risks so far as is reasonably practicable and, if that is not reasonably practicable, minimise them. Regulation 36 of the model WHS Regulations sets the order of controls, and PPE comes last. In the six-level version of the Hierarchy of Controls it is Level 6, the least effective control, because it does not remove the hazard. It only places a barrier between the hazard and the worker, and that barrier depends entirely on correct selection, fit, use and maintenance.
Victoria does not use the model WHS laws. There, the Occupational Health and Safety Act 2004 and OHS Regulations 2017 apply, and they also treat PPE as a last-resort control for specific hazards. Western Australia's Work Health and Safety Act 2020 and regulations follow the model approach.
Despite being the last resort, PPE is required on almost every construction site through site rules and SWMS. The reason is simple: construction involves residual risks that cannot be fully controlled by higher-level measures alone. You might have guardrails (isolation) on a scaffold, but you still wear a hard hat in case something falls from above.
Hard Hats β AS/NZS 1801
Most construction sites require hard hats wherever there is a risk of head injury from falling objects or knocks, and many require them at all times outside site offices and amenities. AS/NZS 1801 Occupational protective helmets sets the requirements for industrial safety helmets in Australia and New Zealand.
- Helmet type: AS/NZS 1801 has more than one helmet type with different performance tests, and the standard was revised in 2024. Check the helmet's label for compliance and its intended use, and make sure it matches what your SWMS or site rules specify
- Inspection: Check for cracks, dents, UV degradation (a chalky or faded surface) and damaged suspension harnesses before each use
- Replacement: Replace a helmet after any significant impact, even if no damage is visible. Otherwise replace the shell and harness at the intervals the manufacturer recommends, which take into account UV exposure and age
- Fit: The suspension harness must sit firmly on the head. Do not wear the hat backwards unless the manufacturer says it is designed for reverse wearing
- Colours: There is no national colour code for hard hats. Some sites use colours to identify roles (for example, supervisors or visitors), but these are site-specific rules, so ask at your induction
Hi-Vis Clothing β AS/NZS 4602.1 and AS/NZS 1906.4
High-visibility clothing helps workers be seen by operators of mobile plant and vehicles. It is one of the most commonly required items on construction sites. AS/NZS 4602.1 covers high-visibility garments for occupational use, and AS/NZS 1906.4 covers the fluorescent and retroreflective materials used in them.
- Day only (Class D): Fluorescent material (yellow, orange, or red) for daytime visibility
- Day/Night (Class D/N): Fluorescent material plus retroreflective tape for visibility in both day and night/low-light conditions
- Night only (Class N): Retroreflective tape on a non-fluorescent background. Used when only night visibility is required
- Selection: Day/night (D/N) garments are needed where work happens in low light, at night or where lighting changes during a shift, and many sites specify D/N as standard. Choose a fluorescent colour that contrasts with the work environment
- Maintenance: Wash according to manufacturer instructions. Faded fluorescent material and damaged retroreflective tape reduce effectiveness significantly
Safety Footwear β AS/NZS 2210.3
Safety boots protect against crushing injuries, puncture wounds from nails and sharp objects, slips and some electrical hazards. Almost all construction sites require safety footwear with protective toe caps. AS/NZS 2210.3 sets the requirements for safety footwear.
- Toe protection: Safety footwear under AS/NZS 2210.3 has toe caps (steel or composite) tested against a 200-joule impact and 15 kN compression
- Penetration resistance: Footwear marked as penetration resistant has a steel or composite midsole that helps stop nails and sharp objects going through the sole. Not all safety boots have this, so check the marking if your site needs it
- Ankle support: Lace-up boots that cover the ankle provide stability on uneven ground
- Slip resistance: Outsoles should be rated for slip resistance on wet and oily surfaces
- Inspection: Check for worn soles, damaged toe caps, broken laces, and sole separation. Replace boots when the protective features are compromised
Eye and Face Protection β AS/NZS 1337.1
Eye injuries from flying particles, dust, chemical splashes, and UV radiation are common on construction sites. Safety glasses or goggles must be worn whenever there is a risk to the eyes.
- Safety glasses: Impact-resistant lenses with side shields. Suitable for general construction tasks with flying particle risk
- Safety goggles: Sealed fit around the eyes. Required for dust, chemical splash, and grinding operations
- Face shields: Full-face protection for grinding, cutting, and tasks with high projectile risk. Worn over safety glasses, not instead of them
- Welding filters: Welding needs filters with the correct shade number for the process and current, as set out in AS/NZS 1338.1
- Marking: Look for AS/NZS 1337.1 compliance markings on the frame and lens
Hand Protection β Gloves
Hands are injured often on construction sites by cuts, crush injuries, burns and chemicals. The correct glove depends on the specific hazard.
- Leather gloves: General-purpose protection against abrasion, cuts, and moderate heat
- Chemical-resistant gloves: Nitrile, neoprene, or PVC for handling solvents, epoxies, and chemicals. Check the SDS for the recommended glove type
- Cut-resistant gloves: High-performance polyethylene (HPPE) or Kevlar for handling sharp materials like sheet metal and glass
- Anti-vibration gloves: Padded gloves are sometimes used with vibrating power tools, but they may reduce only part of the hand-arm vibration, so they do not replace low-vibration tools, tool maintenance and limits on exposure time
- Important: Never wear gloves near rotating machinery (drill presses, lathes) as they can catch and pull the hand into the equipment
Hearing Protection β AS/NZS 1270
The exposure standard for noise is an 8-hour average (LAeq,8h) of 85 dB(A) or a peak of 140 dB(C). A PCBU must make sure no worker is exposed above this standard, using quieter equipment and engineering controls first. Where a risk still remains, workers must be given hearing protection, and many construction tasks need it. Hearing protectors are tested to AS/NZS 1270. Under the model WHS Regulations, workers who are frequently required to wear hearing protection to protect against noise above the standard must be given audiometric testing within 3 months of starting that work and at least every 2 years after that.
- Earplugs: Inserted into the ear canal. Disposable foam plugs or reusable moulded plugs. Effective when properly inserted
- Earmuffs: Cover the entire ear. Easier to fit correctly and monitor compliance. Can be attached to hard hats
- SLC80 rating: The Sound Level Conversion rating indicates the protection level. Match the rating to the noise exposure level
- Over-protection: Do not use hearing protection rated far above the noise level, as over-protection can prevent workers from hearing warnings and communication
- Dual protection: In very high noise environments, earplugs and earmuffs may be worn together where a competent person's assessment shows one protector is not enough
Respiratory Protection β AS/NZS 1716 and AS/NZS 1715
Respiratory protective equipment (RPE) is required when airborne contaminants cannot be controlled to safe levels through other means. Respirators should comply with AS/NZS 1716 (performance), and be selected, used and maintained in line with AS/NZS 1715. The right filter class depends on the contaminant, how much of it is in the air and the type of respirator, so follow the SDS, the SWMS and any regulator guidance for the task.
- P1 filters: Mechanically generated particles, such as dust from sanding or drilling. The lowest particulate class
- P2 filters: Mechanically and thermally generated particles (fine dusts, fumes and mists). Commonly used for silica dust tasks where they give enough protection for the exposure level
- P3 filters: Highly toxic particles. P3 filters are normally used with full-face or powered respirators to get their full protection
- Half-face respirators with cartridges: Organic vapours, solvents, paints. Cartridges must match the contaminant type
- Fit testing: Tight-fitting RPE must be fit-tested to the individual wearer by a competent person before use. There must be no facial hair where the mask seals against the face, as it prevents an effective seal
Employer and Worker Obligations
The model WHS laws place clear duties on both PCBUs and workers regarding PPE:
- PCBU obligations (regulation 44): Provide PPE to workers (unless another PCBU, such as a labour hire company, has already provided it). Make sure it is suitable for the work and the hazard, a suitable size and fit, reasonably comfortable, and maintained, repaired or replaced so it stays clean, hygienic and in good working order. Give workers information, training and instruction on its proper use, wearing and storage
- No charge to workers: A PCBU must not charge or levy a worker for anything done or provided for WHS purposes, which includes required PPE (model WHS Act, s 273)
- Worker obligations (regulation 46): Use or wear the PPE in line with the information, training and reasonable instructions given. Do not intentionally misuse or damage it. Tell the PCBU about any damage, defect or need to clean or decontaminate it
- Other people at the workplace (regulation 47): Visitors and others must also wear PPE where it is required
- Consultation: PCBUs have a duty to consult workers on WHS matters (model WHS Act, s 47), including decisions about control measures such as PPE. Workers who are comfortable with their PPE are more likely to wear it consistently
PPE Inspection Checklist
Before every shift, inspect your PPE:
- Hard hat: No cracks, dents, or UV degradation. Suspension harness intact
- Hi-vis: Fluorescent colour not faded. Reflective tape not peeling or damaged
- Boots: Sole intact, toe cap undamaged, laces secure
- Glasses/goggles: Lenses clear and unscratched. Frame not cracked
- Gloves: No tears, holes, or chemical contamination
- Hearing protection: Earmuff seals not cracked. Earplugs clean and pliable
- Respirator: Straps elastic. Valves functioning. Cartridges within expiry
Key Takeaways
- PPE is the last resort in the Hierarchy of Controls β not the first
- Choose PPE that complies with the relevant Australian/New Zealand Standards, which WHS Codes of Practice and site rules commonly require
- Inspect your PPE before every shift and report any damage
- PCBUs must provide required PPE, must not charge workers for it, and must make sure it fits properly
- Workers must use PPE as instructed β it is a legal obligation
- The right PPE for the job depends on the specific hazard β there is no one-size-fits-all approach
Sources and further reading (last reviewed November 2026)
WHS rules differ between states and change over time. Where this page states a legal or regulatory fact, it is based on the official sources below. If anything here disagrees with them, the official source wins. You can read how we check and correct our content.
- PPE: WHS duties (Safe Work Australia)
- Personal protective equipment in construction: duties tool (Safe Work Australia)
- Work Health and Safety Act 2011 (Cth): Federal Register of Legislation
- Model WHS Regulations, consolidated 1 July 2024, regulations 36, 44-47 and 56-58 (PDF, Safe Work Australia)
- Model Code of Practice: Managing noise and preventing hearing loss at work
- Selecting appropriate RPE: AS/NZS 1716 and 1715, fit testing (SafeWork SA)
- Respiratory protective equipment and fit testing (SafeWork NSW)
- AS/NZS 1801:2024 Occupational protective helmets (Standards Australia store)
- The hierarchy of control (WorkSafe Victoria)
Test Your PPE Knowledge
Practice PPE selection, standards, and compliance questions for your White Card.
Start Practice Test