Hierarchy of Controls Explained
By WhiteCard Prep Team | Last updated: November 2026 | Reading time: 10 min
The Hierarchy of Controls is one of the most important concepts in workplace health and safety, and it appears frequently on the White Card assessment. This guide explains each level of the hierarchy with practical construction examples so you can apply the concept confidently.
Test your knowledge
Practice hierarchy of controls questions in our Hazard Identification topic.
What Is the Hierarchy of Controls?
The Hierarchy of Controls is a systematic approach to eliminating or reducing workplace hazards. It ranks control measures from most effective (elimination) to least effective (personal protective equipment). The principle is simple: always start at the top and work downward. Only move to a lower-level control when higher-level options are not reasonably practicable.
The hierarchy is built into Australian WHS law in two places. Section 17 of the model Work Health and Safety Act requires a duty holder to eliminate risks to health and safety so far as is reasonably practicable and, if that is not reasonably practicable, to minimise them so far as is reasonably practicable. Regulation 36 of the model WHS Regulations ("Hierarchy of control measures") then sets out the order in which control measures must be considered when a risk cannot be eliminated.
In Victoria the model WHS laws do not apply. Victoria uses the Occupational Health and Safety Act 2004 and the Occupational Health and Safety Regulations 2017, and WorkSafe Victoria promotes the same hierarchy of control in its guidance, with elimination at the top and PPE at the bottom. Western Australia applies its own Work Health and Safety Act 2020 and regulations, which follow the model laws closely.
How the Regulations Group the Levels
Many training courses, including White Card courses, teach the hierarchy as six separate steps, and this guide follows that format. The model Regulations and Safe Work Australia's Code of Practice How to manage work health and safety risks group them a little differently:
- First: eliminate the risk, so far as is reasonably practicable
- If the risk cannot be eliminated: minimise it by substitution, isolation or engineering controls, or a combination of them
- If a risk still remains: minimise it further with administrative controls
- If a risk still remains after that: minimise it with suitable personal protective equipment
Both versions put the controls in the same order. The difference is only that the law treats substitution, isolation and engineering controls as one tier rather than three, so you can choose any of them (or combine them) before moving down to administrative controls and PPE.
The Six Levels of the Hierarchy
Level 1: Elimination (Most Effective)
Elimination completely removes the hazard from the workplace. It is the most effective control because if the hazard does not exist, it cannot cause harm. This should always be the first option considered.
Construction Examples:
- Prefabricating wall frames at ground level rather than building them at height β this eliminates the fall hazard entirely
- Designing a building without a need for manual excavation near underground services
- Using pre-cast concrete panels instead of pouring concrete in formwork at height
- Eliminating the need for hot work by using mechanical fasteners instead of welding
Elimination is not always possible, especially on construction sites where hazards are inherent in the work. When elimination is not reasonably practicable, move to the next level.
Level 2: Substitution
Substitution involves replacing a hazardous substance, process, or equipment with something less hazardous. The hazard still exists but is significantly reduced.
Construction Examples:
- Using water-based paint instead of solvent-based paint to reduce toxic fume exposure
- Replacing a noisy pneumatic tool with a quieter electric alternative
- Using pre-mixed concrete instead of mixing on-site (reduces dust and manual handling)
- Substituting a toxic cleaning chemical with a less hazardous biodegradable product
- Using fibreglass ladders instead of aluminium near electrical work
Level 3: Isolation
Isolation separates the hazard from people by distance or a physical barrier. The hazard remains but workers are physically prevented from coming into contact with it.
Construction Examples:
- Installing guardrails around open edges and excavations to prevent falls
- Enclosing a noisy generator inside an acoustic barrier
- Fencing off an asbestos removal area to prevent unauthorised access
- Using lockout/tagout to isolate electrical energy during maintenance
- Setting up exclusion zones around crane operations
Level 4: Engineering Controls
Engineering controls physically change the workplace or the equipment to reduce risk. They do not eliminate the hazard but make it less likely to cause harm.
Construction Examples:
- Installing local exhaust ventilation to capture dust from cutting operations
- Using mechanical lifting aids (forklifts, hoists) to reduce manual handling
- Installing edge protection systems on scaffolding
- Using water suppression on concrete saws to reduce silica dust
- Installing residual current devices (RCDs) on all electrical circuits
- Providing vibration-dampened handles on power tools
Level 5: Administrative Controls
Administrative controls are work practices, procedures, training, and signage that reduce the risk of harm. They rely on human behaviour, which makes them less reliable than physical controls.
Construction Examples:
- Safe Work Method Statements (SWMS) for high-risk construction work
- Job rotation to reduce repetitive strain and vibration exposure
- Safety inductions and toolbox talks
- Speed limits for vehicles and forklifts on site
- Warning signs and hazard labels
- Scheduling noisy work during times when fewer workers are present
- Permit-to-work systems for confined space entry and hot work
Level 6: Personal Protective Equipment (PPE) β Least Effective
PPE is the last resort in the hierarchy. It protects individual workers but does not reduce or eliminate the hazard itself. PPE relies on correct selection, fit, use, and maintenance, which makes it the least reliable control.
Construction Examples:
- Hard hats to protect against falling objects
- Safety boots with steel or composite toe caps
- Hi-vis clothing for visibility
- Safety glasses and goggles for eye protection
- Hearing protection (earplugs or earmuffs) for noise exposure
- Respiratory protection (P2 masks) for dust and fume exposure
- Full-body harnesses as fall arrest systems
Why the Order Matters
The hierarchy is ordered by effectiveness and reliability. Controls at the top (elimination, substitution) are inherently more reliable because they remove or reduce the hazard at the source. Controls at the bottom (administrative, PPE) rely on human behaviour, which is subject to error, complacency, and non-compliance.
For example, consider the risk of silica dust from cutting concrete:
- Elimination: Use pre-cut concrete panels (no cutting needed on site)
- Substitution: Use a material that does not contain silica
- Engineering: Use a wet-cutting method with water suppression and local exhaust ventilation
- Administrative: Limit cutting time, train workers on dust hazards, monitor air quality
- PPE: Provide P2 respirators (last resort, relies on correct fit and consistent use)
In practice, controls from different levels are often combined. The Regulations expressly allow a combination of control measures, and administrative controls and PPE are normally used to support higher-level controls, not to replace them.
Hierarchy of Controls on the White Card Test
The White Card test frequently asks questions about the hierarchy. Common question types include:
- "What is the most effective control measure?" β Answer: Elimination
- "What is the least effective control?" β Answer: PPE
- "Which is an example of an engineering control?" β Look for physical modifications
- "Which is an example of substitution?" β Look for replacing something hazardous with something less hazardous
- "Why is PPE considered the last resort?" β Because it does not reduce the hazard and relies on correct use
Key Takeaways
- Always start at the top of the hierarchy (elimination) and work down
- Higher-level controls are more effective and reliable than lower-level ones
- PPE should never be the primary control β it is the last resort
- Multiple controls from different levels can be combined for better protection
- The duty to eliminate or minimise risk is in section 17 of the model WHS Act, and the order of controls is in regulation 36 of the model WHS Regulations (Victoria uses its own OHS laws)
- Understanding the hierarchy is essential for passing the White Card test
Sources and further reading (last reviewed November 2026)
WHS rules differ between states and change over time. Where this page states a legal or regulatory fact, it is based on the official sources below. If anything here disagrees with them, the official source wins. You can read how we check and correct our content.
- Work Health and Safety Act 2011 (Cth), section 17: Federal Register of Legislation
- Model WHS Regulations, consolidated 1 July 2024, regulation 36 (PDF, Safe Work Australia)
- Model Code of Practice: How to manage work health and safety risks (Safe Work Australia)
- Managing risks: identify, assess and control hazards (Safe Work Australia)
- The hierarchy of control (WorkSafe Victoria)
- Occupational Health and Safety Act 2004 and Regulations 2017 (WorkSafe Victoria)
Test Your Knowledge
Practice hierarchy of controls questions with our free White Card test.
Start Practice Test