Forklift Safety
Forklifts are involved in serious injuries and deaths at Australian workplaces every year, and pedestrians are among those most often hurt. This section covers forklift licensing (high risk work licence class LF), pre-operational inspections, load capacity and centre of gravity, operating on inclines, pedestrian safety zones, refuelling procedures, and the legal requirements for forklift operation in Australia.
Study Guide: Forklift Safety
Review these sample questions before starting the practice test.
Q1: What licence is required to operate a forklift in Australia?
- A. A standard car licence
- B. A High Risk Work Licence (HRWL) with LF class β TLILIC0003 β
- C. No licence is required
- D. A truck licence
Operating a forklift requires a High Risk Work Licence (HRWL) in the LF class (forklift truck), obtained after completing the TLILIC0003 'Licence to operate a forklift truck' unit and being assessed. A White Card (CPCWHS1001) alone does not allow you to operate a forklift.
Q2: What is the purpose of a pre-start (pre-operational) check on a forklift?
- A. To warm up the engine
- B. To check for defects, damage, and ensure the forklift is safe to operate before use β
- C. To count how many hours the forklift has been used
- D. To check the fuel price
A pre-start check identifies defects or damage before operation. It covers tyres, forks, mast, hydraulics, brakes, steering, lights, horn, seatbelt, and fluid levels.
Q3: What should you do if you find a defect during a pre-start check?
- A. Operate the forklift carefully
- B. Report the defect, tag the forklift as out of service, and do not operate it until repaired β
- C. Fix it yourself
- D. Ignore minor defects
If a defect is found, the forklift must not be operated. Report the defect to the supervisor, attach a defect tag, and lock out the forklift until a qualified person repairs it.
Q4: What is the rated capacity of a forklift?
- A. The total weight of the forklift
- B. The maximum load the forklift can safely lift at the standard load centre under specified conditions β
- C. The speed of the forklift
- D. The number of workers it can carry
Rated capacity is the maximum weight the forklift can safely lift at the standard load centre (typically 500mm for counterbalance) at a specified mast height. This is shown on the data plate.
Q5: Where can you find the rated capacity of a forklift?
- A. On the ignition key
- B. On the data plate (capacity plate) attached to the forklift β
- C. In the glove box
- D. Written on the forks
The data plate (capacity plate) is attached to the forklift and shows the rated capacity, load centre distance, maximum lift height, and the forklift's weight.
Q6: What is the load centre distance on a forklift?
- A. The distance between the two forks
- B. The horizontal distance from the face of the forks to the centre of gravity of the load β
- C. The distance the forklift can travel with a load
- D. The height of the mast
Load centre distance is the horizontal distance from the vertical face of the forks to the centre of gravity of the load. Standard is typically 500mm or 600mm. Loads with a greater load centre reduce capacity.
Q7: What happens if you exceed the rated capacity of a forklift?
- A. The forklift goes slower
- B. The forklift may tip forward, lose stability, and the load could fall β risking serious injury or death β
- C. Nothing β forklifts have a large safety margin
- D. The engine stalls
Exceeding the rated capacity can move the combined centre of gravity forward past the front axle, so the forklift tips forward or loses steering and braking control, and the load can fall. Overloading and tip-overs are a known cause of serious forklift incidents.
Q8: What is the "stability triangle" on a counterbalance forklift?
- A. A warning sign
- B. The triangular area formed by the two front wheels and the rear axle pivot point that determines tipping stability β
- C. A type of forklift attachment
- D. The driver's seatbelt arrangement
The stability triangle is formed by the two front axle ends and the rear axle pivot. The combined centre of gravity (forklift + load) must remain within this triangle to prevent tipping.
Ready to practice all 66 questions? Start the interactive quiz below.
What is the load centre distance on a forklift?
More Forklift Safety Questions
8 more worked examples with answers and explanations.
Q9: When travelling with a load on a forklift, the forks should be:
- A. Raised as high as possible for visibility
- B. Lowered to approximately 150-200mm above the ground and tilted slightly back β
- C. Touching the ground
- D. At head height of pedestrians
When travelling, forks should be lowered to 150-200mm above the ground and tilted slightly back to lower the centre of gravity and secure the load. This maximises stability.
Q10: What is the correct procedure when driving a forklift on a ramp or incline with a load?
- A. Drive down the ramp with the load facing downhill
- B. Drive up the ramp with the load facing uphill (load leading) and reverse down with the load uphill β
- C. Always drive sideways on ramps
- D. Speed up to maintain momentum
On ramps, always keep the load on the uphill side for stability. Drive forward up the ramp (load uphill) and reverse down the ramp (load uphill). Never turn on a ramp.
Q11: Can a forklift be used to lift people?
- A. Yes, anytime
- B. Yes, standing on the forks is acceptable
- C. Only with an approved personnel work platform (safety cage) secured to the forks with appropriate safeguards β
- D. No, never under any circumstances
People may only be elevated on a forklift using an approved personnel work platform (safety cage) that is properly secured to the forks, with guardrails, and following specific safety procedures.
Q12: What should a forklift operator do at blind corners and intersections?
- A. Speed up to get through quickly
- B. Stop or slow down, sound the horn, and check for pedestrians and other traffic before proceeding β
- C. Honk and drive through
- D. Only check if they hear someone
At blind corners and intersections, the operator must slow or stop, sound the horn, check mirrors and look in all directions for pedestrians and other vehicles before proceeding carefully.
Q13: What is the main cause of forklift tip-over accidents?
- A. Engine failure
- B. Turning too fast, overloading, driving on uneven surfaces, or lifting loads too high while travelling β
- C. Flat tyres
- D. Rain
Forklift tip-overs are primarily caused by excessive speed during turns, overloading, driving on uneven or sloped surfaces, and travelling with elevated loads, all of which shift the centre of gravity.
Q14: What should you do if a forklift starts to tip over?
- A. Jump off immediately
- B. Stay in the seat, hold the steering wheel, brace your feet, and lean away from the direction of the tip β
- C. Try to steer to correct it
- D. Stand up in the cabin
If a forklift tips, stay in the seat with the seatbelt on, hold the steering wheel firmly, brace your feet, and lean away from the direction of the fall. Jumping out can result in being crushed.
Q15: Why must the operator wear a seatbelt on a forklift?
- A. It is not required on forklifts
- B. To keep the operator secured in the operator compartment in the event of a tip-over, preventing them from being thrown or crushed β
- C. Only for travelling long distances
- D. Only on rough terrain
The seatbelt keeps the operator inside the protective structure (overhead guard or ROPS) during a tip-over. Without it, the operator may be thrown out and crushed by the forklift or its overhead guard.
Q16: What is the safe distance a forklift must maintain from pedestrians?
- A. No minimum distance
- B. At least 3 metres where practicable, with exclusion zones and dedicated pedestrian walkways β
- C. 50 centimetres
- D. Only 1 metre
WorkSafe Victoria guidance says pedestrians should keep at least 3 metres from a forklift travelling at walking pace with the load at axle height, and more for raised loads (3 metres plus the height of the mast and load). Sites should also use exclusion zones, dedicated pedestrian walkways and physical barriers to separate pedestrians from forklifts.
Key facts for this topic
- Operating a forklift truck requires a high risk work licence of class LF (order-picking forklifts are class LO). A White Card on its own does not allow you to operate a forklift. Source
- The LF licence is gained by completing TLILIC0003 Licence to operate a forklift truck and passing an assessment, then applying to the state or territory regulator. Source
- A person training for a licence may operate a forklift only under the supervision of a licence holder as part of that training. Source
Common mistakes
The classic mistake is thinking a forklift licence covers every type of lifting machine. LF covers forklift trucks other than order pickers; other plant such as telehandlers, cranes and elevating work platforms have their own licence classes or competency requirements. Questions also test pre-start checks and pedestrian separation, so learn those as procedures rather than rules of thumb.
Keep studying
Sources and further reading (last reviewed November 2026)
WHS rules differ between states and change over time. Where this page states a legal or regulatory fact, it is based on the official sources below. If anything here disagrees with them, the official source wins. You can read how we check and correct our content.
By WhiteCard Prep Team Last reviewed: November 2026. WHS laws differ between states and territories; Victoria uses its own OHS laws. Check your state regulator for local rules.
Continue Studying
This guide is free and kept up to date by one person. β Support it